Dummy War System Requirements: What You Need to Play It and Clip It Smoothly
No official Dummy War spec sheet exists yet. Here's what to check before playing this Roblox shooter and recording clips with Medal.
The Short Answer: Dummy War Has No Standalone Spec Sheet
If you went looking for a Dummy War system requirements list and came up empty, you're not alone. Dummy War is a Roblox experience, not a standalone download, so there's no separate "minimum" and "recommended" hardware table published for it. In practice, the only real hardware question is whether your machine runs Roblox smoothly—and whatever tool you use to record and share your matches.
This matters because players often blame the game for stutter when the recording software is the actual bottleneck. Below is what the available material actually establishes, what it doesn't, and how to check your own setup before you queue up.
What We Know About Dummy War Itself
The game is a team-based shooter built inside Roblox. According to the game's own description, two teams fight for points on a map with no time limit, so matches run until one side takes control. The premise: Dummy rebels have started occupying Dummy's city, and the Dummy army is defending it.
Key details from the Dummy War game page on Medal.tv:
- Genre: Team-based first-person shooter inside Roblox
- Match format: Point-based, endless, no timer
- Controls: R to reload, F to load, C to crouch and lay down, X to disable, V to switch weapon mode, Q and E to lean left and right (tap again to cancel)
- Developer: Builder @New77vovo77, who is also listed as the tester
Because it runs on Roblox, your baseline performance is tied to how well the Roblox client handles your hardware. Roblox publishes its own system requirements for the client, and those—not a Dummy War-specific list—are what you should compare against your PC. The source material does not include a separate hardware table for this experience.
What the Sources Do Establish: Recording Specs
The one set of concrete specs in the available material belongs to Medal, the clipping tool used to capture Roblox gameplay. If your goal is to record Dummy War clips, these are the numbers that actually apply to your machine:
| Component | Requirement |
|---|---|
| Operating system | Windows 10 or later |
| Platforms supported | PC and mobile (console captures can be imported) |
| RAM impact while running | Roughly 100–400 MB |
| Maximum recording resolution | Up to 4K |
| Frame rate | Up to 144fps, with 60fps enabled by default |
| GPU acceleration | NVIDIA, AMD, and Intel supported, plus CPU-based recording |
| Encoding formats | H.264, H.265, HEVC, and AV1 |
| File output | MP4, saved locally and to the cloud |
The takeaway: the recording layer is deliberately lightweight. A 100–400 MB memory footprint is small enough that low-spec systems can multitask, and Medal's own documentation notes that variable recording settings and cloud storage make even a modest "potato PC" workable.
How to Check Your Setup Before You Play
Rather than guessing, run a quick self-audit. None of these steps require special tools, and each one maps to a spec above.
- Confirm your OS. If you're on Windows 10 or newer, you're inside Medal's supported range. Older versions are not listed as compatible.
- Launch Roblox first, then your recorder. Play one full Dummy War match with nothing else running. If it's smooth, the game is fine on your hardware.
- Add recording second. Start clipping and play another match. Any new stutter points at capture settings, not the game itself.
- Lower settings in order of cost. Frame rate first (drop from 144fps toward 60fps), then resolution, then codec.
- Check your GPU vendor. If you have NVIDIA, AMD, or Intel graphics, enable GPU acceleration instead of CPU-based recording to offload the work.
Tips for Smoother Dummy War Sessions
Cap your frame rate. Recording at 144fps is supported, but 60fps is the default for good reason—it's a much lighter load while still looking clean on playback.
Use GPU encoding. Letting your graphics card handle encoding frees the CPU to keep the game running, which matters most during the endless, crowded fights Dummy War is built around.
Grab clips after the fact, not during. A hotkey-based instant replay captures the last few minutes of gameplay without alt-tabbing out mid-match—useful when matches have no timer and a good firefight can happen at any moment.
Match your capture resolution to your display. Recording at 4K when you play at 1080p adds file size without adding visible detail.
Keep clips in the cloud. Local storage fills up fast with long, untimed matches; cloud backup keeps your highlight reel intact.
What the Material Doesn't Cover
To be direct about the limits of the available information: there is no published Dummy War-specific CPU, GPU, or RAM requirement, and the developer has not posted one in the material reviewed here. Community reports and player experience on performance are also not documented in the source—the game's Medal page currently lists no clips, so there's no crowd-sourced performance data to reference yet.
If you need a hard number, use Roblox's official client requirements as your floor and the recording specs above as your ceiling. Anything that runs Roblox comfortably will run Dummy War; the question is only how much recording overhead you want on top.
FAQ
Do I need a gaming PC to play Dummy War? No dedicated spec list exists because Dummy War is a Roblox experience. Your performance depends on how well the Roblox client runs on your machine.
What are the system requirements for recording Dummy War? Medal requires Windows 10 or later on PC and can also run on mobile. It uses roughly 100–400 MB of RAM while active.
Can I record Dummy War in 4K? Yes. Recording resolution is customizable up to 4K, with frame rates up to 144fps.
Will recording software lag the game? Medal is built to be lightweight, with a 100–400 MB memory footprint, and supports GPU acceleration on NVIDIA, AMD, and Intel hardware to reduce strain.
Is the recording tool free? Yes—it's free on PC and mobile, with optional paid premium features.
Does it work on console? Not natively. Console system captures can be imported for editing and sharing instead.